New
IPX IN-PLACE EXTENSOMETER
The In-Place Extensometer (IPX) offers automated monitoring of standard magnetic extensometer installations. The system is designed for a simple, adaptable installation with a single cable connection at the top of the borehole. Its large measurement range accommodates large levels of settlement or heave, and ease of adjustment means it can be reconfigured for changed site conditions such as embankment filling or cutting.
Description
- Compatible
The IPX can be installed in most standard magnetic extensometer installations. It is compatible with most leading digital geotechnical data loggers and its low power consumption allows over 50 sensors to be connected to a single battery powered logger.
- Adaptable
Easily raised through fill or reduced with cutting – the IPX’s distinct bottom-supported configuration allows easy extension or reduction without interfering with the existing sensors.
- Adjustable
A unique coiled cable system allows adjustment of the sensor spacing according to site conditions. The cable’s coiled section allows 500mm of adjustment to the sensor’s position within the borehole.
Additional information
| Brands | |
|---|---|
| Range |
400mm |
| Resolution |
0.1mm |
| Accuracy |
±0.5mm |
| Signal output |
Digital RS-485, Modbus |
| Power supply |
4-30VDC |
| Power consumption (idle/ active) |
229mW/ 87mW |
| Time per measurement (warm-up/ reading) |
20.3 seconds/ 2 seconds |
| Temperature range |
-40°C to 80°C |
| Max sensors per string |
27 |
| Max length of string |
100m |
Reviews (0)
About brand
Osprey Measurement Systems was founded in partnership with University College London’s Civil, Environmental and Geomatic Engineering Department, with the goal of applying innovative measurement techniques to monitoring challenges within the civil and geotechnical engineering space. Their products are designed, developed, and manufactured in the UK under a certified ISO-compliant quality management system. With a wealth of experience managing geotechnical and structural monitoring programs, Osprey’s management place a key emphasis on
Data Sheets
Related products
DRIVE-IN PIEZOMETERS WP-3400 & SGP-3500 SERIES
In stock
Drive-in piezometers, also referred to as push-in piezometers, are designed for installing in soft clays, organic or fine grained cohesionless soils typically with a SPT-N value less than 10. They are available with a CPT fitting or 1” BSP thread.
Depending on the depth and type of soil, they can either be pushed directly into the soil from ground level to the required depth or pushed into the base of a CPT test or drilled borehole.
PRESSURE TRANSDUCER VWT-9000 SERIES
In stock
The Geosense® VWT-9000 Series of Pressure Transducers are designed to be connected directly into hydraulic or pneumatic pressure lines by means of a 1/4” BSPF thread. Other thread sizes are available on request.
They are typically used to monitor uplift pressures within dams and to enable manual standpipe piezometers to be upgraded into an automated data acquisition system.
TRIAXIAL TILT SENSOR NODE
In stock
SUBMERSIBLE TILT METER
In stock
TILT BEAM
In stock
The Tilt Beam is a lightweight, rigid aluminium beam that is used in conjunction with a Triaxial Tilt Node, a NanoPlus or a NanoMacro.
The tilt beam has been successfully used in many applications, including:
- Movement monitoring of any structure
- Longitudinal settlement
- Tunnel convergence/divergence
- Lateral displacements
STANDPIPE PIEZOMETER
In stock
TILT BEAM MEMS
In stock
MEMS Tilt Beams are designed for attachment to structures, on either a vertical or horizontal surface, for the measurement of tilt or differential settlement.
They consist of a highly accurate MEMS sensor housed in a fully sealed enclosure which is mounted on a lightweight rigid GRP beam. This can be mounted onto the structure using special anchors. The GRP beam has a very low coefficient of thermal expansion meaning that thermal affects are minimised.
INCLINOMETER CASING XC
In stock
Reviews
There are no reviews yet.