LOAD CELL FOR TUNNEL LININGS AND STRUTS
This type of load cell is used to monitor stresses in steel linings, struts, piles and support beams.
It consists of a sensitive pressure pad formed by joining two stiff steel discs at their periphery. The void inside the cell is filled with de-aired fluid. When load is applied to the cell the pressure of the inside liquid changes. The changes in pressure correspond directly to the load applied.
The pressure in the loads cell is measured by a resistance transducer.
Categories: Geo-Structural Instruments, Load Cells
Description
Mounting surfaces should be flat and parallel for optimum performance and the use of very stiff bearing plates and load distribution plates is recommended. Electric cable connects the load cells to a suitable remote readout system.
Additional information
Brands | |
---|---|
Measuring range |
1,900 & 3,000 kN |
Accuracy |
>1% FS |
Linearity |
+/-0.25% FS |
Signal output |
4-20 mA (current loop) |
Repeatability |
> +/- 0.02% FS |
Admissible loads |
150% FS |
Ultimate tensile strengths |
300% FS |
Operating temperature |
-20°C ~ +80°C |
Reviews (0)
Be the first to review “LOAD CELL FOR TUNNEL LININGS AND STRUTS” Cancel reply
About brand
Geosense Ltd is one of Europe’s leading manufacturers and suppliers of instruments to the geotechnical, civil engineering, mining and environmental industries.
Geosense products are used globally in major projects in more than 68 countries. With a comprehensive in-house design and manufacturing capability, we can provide products not only to tight deadlines but also to suit custom-engineered solutions for specific project requirements.
Geosense specialises in the manufacture of vibrating wire and MEMS sensors, which are used to produce a wide range of instruments. In addition we manufacture automated data acquisition systems to complement our sensors, including wireless systems.
Data Sheets
Related products
MULTI-POINT VW PIEZOMETER
In stock
Rated 0 out of 5
DRIVE-IN PIEZOMETERS WP-3400 & SGP-3500 SERIES
In stock
Rated 0 out of 5
Drive-in piezometers, also referred to as push-in piezometers, are designed for installing in soft clays, organic or fine grained cohesionless soils typically with a SPT-N value less than 10. They are available with a CPT fitting or 1” BSP thread.
Depending on the depth and type of soil, they can either be pushed directly into the soil from ground level to the required depth or pushed into the base of a CPT test or drilled borehole.
PRESSURE TRANSDUCER VWT-9000 SERIES
In stock
Rated 0 out of 5
The Geosense® VWT-9000 Series of Pressure Transducers are designed to be connected directly into hydraulic or pneumatic pressure lines by means of a 1/4” BSPF thread. Other thread sizes are available on request.
They are typically used to monitor uplift pressures within dams and to enable manual standpipe piezometers to be upgraded into an automated data acquisition system.
TILT BEAM
In stock
Rated 0 out of 5
The Tilt Beam is a lightweight, rigid aluminium beam that is used in conjunction with a Triaxial Tilt Node, a NanoPlus or a NanoMacro.
The tilt beam has been successfully used in many applications, including:
- Movement monitoring of any structure
- Longitudinal settlement
- Tunnel convergence/divergence
- Lateral displacements
IN-PLACE INCLINOMETER (IPI)
In stock
Rated 0 out of 5
PENDULUM SYSTEM
In stock
Rated 0 out of 5
HPS-3500 (Hanging) and IPS-3000 (Inverted) Pendulums are used to measure the tilt or rotation by measuring the relative internal horizontal displacement of points along a true vertical line. Each has a tensioned, stainless steel wire and the effects of the earth gravitational forces to guarantee a perfectly vertical line between a fixed point and a tensioning mechanism. Typical applications include concrete dams, bridges and high rise buildings.
IMAGING & CAMERA
In stock
Rated 0 out of 5
The FlatMesh 4G Camera is a best in class solar powered solution for static imagery in remote or industrial areas.
It contains a monochrome digital camera which can take clear, high quality photographs day or night without the use of external illuminators.
The 4G camera connects to a Senceive EdgeHub (with FlatMesh) unit which provides power and connectivity over the cellular network (2G/3G/4G) or existing wired ethernet networks.
INCLINOMETER CASING XC
In stock
Rated 0 out of 5
Reviews
There are no reviews yet.