VW DISPLACEMENT GAUGE VWDT-5000
Geosense® VWDT-5000 series of vibrating wire displacement transducers cover displacement ranges up to 300mm and are fully waterproof to a minimum of IP68 (16 bar external pressure). They can be incorporated into many displacement products such as crack and joint meters, convergence meters, soil extensometers and displacement meters.
Description
VWDT-5000 transducers are particularly rugged, and are carefully constructed and thermally aged to minimise long term drift and changes in calibration. The gauges will withstand demanding environmental factors encountered in Civil Engineering construction sites such as tunnels and piling applications.
The data from the VWDT-5000 can be monitored by means of a portable read-out unit or connected to a data logger and distributed if required by telemetry.
Vibrating wire instruments output a frequency signal, and are therefore insensitive to resistance changes in connecting cables caused by contact resistance or leakage to ground. Cable may be readily and simply extended on site without special precautions. Gauges may be read up to 1000 metres away from their installed location, without change in calibration.
Instruments may be read by any commercially available Vibrating wire readout system operating on either the pluck pulse or swept frequency excitation principle, provided that these units operate over the frequency range of the instruments. In addition, these instruments can be data-logged by a variety of data-loggers equipped with vibrating wire excitation modules including Campbell Scientific and Datataker units.
Units are supplied with a M6 female threaded connection on the measuring plunger.
Additional information
| Brands | |
|---|---|
| Ranges |
5, 12.5, 25, 50, 75, 100, 150, 200, 300, 500mm |
| Resolution |
0.025% FS |
| Accuracy |
±0.1% FS |
| Non linearity |
<0.5% |
| Operating temperature range |
-20 °C +80 °C |
Reviews (0)
About brand
Geosense Ltd is one of Europe’s leading manufacturers and suppliers of instruments to the geotechnical, civil engineering, mining and environmental industries.
Geosense products are used globally in major projects in more than 68 countries. With a comprehensive in-house design and manufacturing capability, we can provide products not only to tight deadlines but also to suit custom-engineered solutions for specific project requirements.
Geosense specialises in the manufacture of vibrating wire and MEMS sensors, which are used to produce a wide range of instruments. In addition we manufacture automated data acquisition systems to complement our sensors, including wireless systems.
Data Sheets
Related products
VWPHT-3600 SERIES
In stock
The VWPHT-3600 series High Temperature Piezometers are suitable for the extreme environments of temperature and pressure found within applications such as geothermal heat and enhanced oil recovery systems including steam assisted gravity drainage (SAGD) and cyclic steam stimulation (CSS). They are capable of monitoring high temperatures up to 250°C and pressures up to 34.5 MPa.
DRIVE-IN PIEZOMETERS WP-3400 & SGP-3500 SERIES
In stock
Drive-in piezometers, also referred to as push-in piezometers, are designed for installing in soft clays, organic or fine grained cohesionless soils typically with a SPT-N value less than 10. They are available with a CPT fitting or 1” BSP thread.
Depending on the depth and type of soil, they can either be pushed directly into the soil from ground level to the required depth or pushed into the base of a CPT test or drilled borehole.
OPTICAL DISPLACEMENT SENSOR NODE
In stock
TRIAXIAL TILT SENSOR NODE
In stock
IN-PLACE TILT METER MEMS
In stock
STANDPIPE PIEZOMETER
In stock
PENDULUM SYSTEM
In stock
HPS-3500 (Hanging) and IPS-3000 (Inverted) Pendulums are used to measure the tilt or rotation by measuring the relative internal horizontal displacement of points along a true vertical line. Each has a tensioned, stainless steel wire and the effects of the earth gravitational forces to guarantee a perfectly vertical line between a fixed point and a tensioning mechanism. Typical applications include concrete dams, bridges and high rise buildings.
MAGNETIC EXTENSOMETER GXM RANGE
In stock
The GEO-XM settlement system is a magnet extensometer system used typically to monitor settlement and heave in foundations, excavations and embankments.
Data received identifies the depth and position where settlement has occurred as well as the total amount of settlement.
It can also be installed behind retaining structures, such as sheet piles and slurry walls, and above underground openings, such as tunnels and shafts.
Reviews
There are no reviews yet.