VW PIEZOMETER VWP-3000 SERIES
The VWP-3000 Series of Vibrating Wire piezometers use the well-proven method of converting fluid pressures on a sensitive diaphragm into a frequency signal.
FEATURES
- Reliable long-term performance
- Rugged, suitable for demanding environments
- High accuracy
- Insensitive to long cable lengths
Description
The VWP-3000 Series of Vibrating Wire piezometers use the well-proven method of converting fluid pressures on a sensitive diaphragm into a frequency signal.
Frequency signals are particularly suitable for the demanding environment of Civil Engineering applications, since the signals are capable of long transmission distances without degradation, tolerant of wet wiring conditions and resistant to external electrical noise.
Key applications include measuring pore pressure in soils and rocks and fluid pressures in hydro-fractures and pump tests.
Models in the VWP-3000 range are:
- VWP-3000 (STANDARD) Standard construction with high & low air entry filters to measure groundwater elevations and pore pressures.
- VWP-3310 (STANDARD VENTED) Standard construction but vented to compensate for barometric pressure changes. Available with high & low air entry filters.
- VWP-3100 (HEAVY DUTY) Heavy duty body for direct burial in fills and dam embankments. Available with high & low air entry filters, standard and heavy duty cable.
- VWP-3200 (LOW PRESSURE) Low pressure version to measure groundwater elevations and pore pressures. Available with high & low air entry filters.
- VWP-3300 (LOW PRESSURE VENTED) Low pressure vented version to compensate for barometric pressure changes. Available with high & low air entry filters.
- VWP-3400 (DRIVE-IN) Drive-in version available for use with SPT rods.
- VWP-3401 (DRIVE-IN) Drive-in version available for use with 1” BSP adaptor.
Additional information
| Brands | |
|---|---|
| Pressure Range |
345, 518, 690 kPa 1, 2, 3.5, 5, 7 10, 20 MPa |
| Over Range Pressure |
1.5 |
| Resolution |
0.025% FS |
| Accuracy |
± 0.1% FS |
| Non Linearity |
<0.5% FS |
| Calbibration Temp Range |
– 20 to + 80 °C |
| Thermal Effect |
<0.05% FS/°C |
| Materials |
316 Stainless Steel |
| Operating Temp Range |
0 to +80°C |
| Over Voltage Protection |
90V Gas Plasma Arrester |
| Thermistor |
3k Ohms @ 25°C |
| Frequency Range |
1850-3500 Hz |
Reviews (0)
About brand
Geosense Ltd is one of Europe’s leading manufacturers and suppliers of instruments to the geotechnical, civil engineering, mining and environmental industries.
Geosense products are used globally in major projects in more than 68 countries. With a comprehensive in-house design and manufacturing capability, we can provide products not only to tight deadlines but also to suit custom-engineered solutions for specific project requirements.
Geosense specialises in the manufacture of vibrating wire and MEMS sensors, which are used to produce a wide range of instruments. In addition we manufacture automated data acquisition systems to complement our sensors, including wireless systems.
About Brand
Geosense specialises in the manufacture of vibrating wire and MEMS sensors, which are used to produce a wide range of instruments. In addition we manufacture automated data acquisition systems to complement our sensors and a range of inherently safe pneumatic pumps for use in the environmental sector.
Data Sheets
Related products
DRIVE-IN PIEZOMETERS WP-3400 & SGP-3500 SERIES
In stock
Drive-in piezometers, also referred to as push-in piezometers, are designed for installing in soft clays, organic or fine grained cohesionless soils typically with a SPT-N value less than 10. They are available with a CPT fitting or 1” BSP thread.
Depending on the depth and type of soil, they can either be pushed directly into the soil from ground level to the required depth or pushed into the base of a CPT test or drilled borehole.
TRIAXIAL TILT SENSOR NODE
In stock
PORTABLE MEMS INCLINOMETER
In stock
The MEMS Portable Inclinometer system utilises modern communication and Smart devices to enable the tilt data generated by the probe to be managed, stored and transferred directly from site via FTP, API, email or other communication platforms.
It is available for vertical, inclined and horizontal applications.
IN-PLACE INCLINOMETER (IPI)
In stock
TILT BEAM MEMS
In stock
MEMS Tilt Beams are designed for attachment to structures, on either a vertical or horizontal surface, for the measurement of tilt or differential settlement.
They consist of a highly accurate MEMS sensor housed in a fully sealed enclosure which is mounted on a lightweight rigid GRP beam. This can be mounted onto the structure using special anchors. The GRP beam has a very low coefficient of thermal expansion meaning that thermal affects are minimised.
WATER LEVEL METER
In stock
MAGNETIC EXTENSOMETER GXM RANGE
In stock
The GEO-XM settlement system is a magnet extensometer system used typically to monitor settlement and heave in foundations, excavations and embankments.
Data received identifies the depth and position where settlement has occurred as well as the total amount of settlement.
It can also be installed behind retaining structures, such as sheet piles and slurry walls, and above underground openings, such as tunnels and shafts.
REED SWITCH PROBE
In stock
Reviews
There are no reviews yet.