HYDRAULIC ANCHOR LOAD CELL HLC-6000
The Geosense® HLC-6000 series Hydraulic Anchor Load Cells consist of a sensitive pressure pad formed by joining two stiff steel discs at their periphery. The void inside the cell is filled with de-aired fluid. When load is applied to the cell the pressure of the inside liquid changes. The changes in pressure correspond directly to the load applied.
Manufactured with a center hole to accommodate anchors, rock bolts and tendons.
The pressure in the loads cell is measured either by a manometer or a vibrating wire transducer (VWDT-5000) and are available in the following models:
- HLC-6000 – Manometer (scale in kN) for pressure indication
- HLC-6500 – Vibrating wire transducer
Model HLC-6500 can be read with a VW-2106 direct readout or connected into a GeoLogger data acquisition system.
Mounting surfaces should be flat and parallel for optimum performance and the use of very stiff abutment plates and load distribution plates is recommended.
The abutment plate (provided locally) is normally made to suit specific site requirements and the load distribution plate (supplied by Geosense) should be inserted between the load cell and the anchor head.
| Brands | Geosense |
|---|---|
| Range | 250 to 2000kN |
| Internal diameters | 40, 71, 92, 110, 130, 165, 190, 210mm |
| Over range capacity | 20% FS |
| Resolution | HLC-6000: 0.5% FS; HLC-6500:0.025% FS |
| Accuracy | HLC-6000: manometer class ±1 % FS; HLC-6500: ± 1.0% FS |
| Temperature range | -30°C to + 85°C |
| Output signal | HLC-6000: Manual; HLC-6500: Frequency |
Related products
STRAIN GAUGE PIEZOMETER SGP-3400 SERIES
In stock
The SGP-3400 Series of strain gauge piezometers are designed for monitoring soil pore pressure or changes in water level and are also suitable for dynamic monitoring such as pumping tests.
They are accurate, highly-reliable and suitable for use in the harsh environments often found within civil engineering including water wells, boreholes, dams, reservoirs, rivers, tanks or any other body of water.
DRIVE-IN PIEZOMETERS WP-3400 & SGP-3500 SERIES
In stock
Drive-in piezometers, also referred to as push-in piezometers, are designed for installing in soft clays, organic or fine grained cohesionless soils typically with a SPT-N value less than 10. They are available with a CPT fitting or 1” BSP thread.
Depending on the depth and type of soil, they can either be pushed directly into the soil from ground level to the required depth or pushed into the base of a CPT test or drilled borehole.
PRESSURE TRANSDUCER VWT-9000 SERIES
In stock
The Geosense® VWT-9000 Series of Pressure Transducers are designed to be connected directly into hydraulic or pneumatic pressure lines by means of a 1/4” BSPF thread. Other thread sizes are available on request.
They are typically used to monitor uplift pressures within dams and to enable manual standpipe piezometers to be upgraded into an automated data acquisition system.
TRIAXIAL TILT SENSOR NODE
In stock
PORTABLE MEMS INCLINOMETER
In stock
The MEMS Portable Inclinometer system utilises modern communication and Smart devices to enable the tilt data generated by the probe to be managed, stored and transferred directly from site via FTP, API, email or other communication platforms.
It is available for vertical, inclined and horizontal applications.
WATER LEVEL METER
In stock
PENDULUM SYSTEM
In stock
HPS-3500 (Hanging) and IPS-3000 (Inverted) Pendulums are used to measure the tilt or rotation by measuring the relative internal horizontal displacement of points along a true vertical line. Each has a tensioned, stainless steel wire and the effects of the earth gravitational forces to guarantee a perfectly vertical line between a fixed point and a tensioning mechanism. Typical applications include concrete dams, bridges and high rise buildings.
INCLINOMETER CASING XC
In stock

Reviews
There are no reviews yet.