VW DISPLACEMENT GAUGE VWDT-6000
The VWDT-6000 series of spring-loaded vibrating wire displacement transducers which cover displacement ranges up to 75mm and are fully waterproof to a minimum of IP68 (16 bar external pressure). They can be incorporated into many displacement products such as crack joint meters, convergence meters, soil extensometers and displacement meters.
Description
VWDT-6000 transducers are particularly rugged and are carefully constructed and thermally aged to minimise long term drift and changes in calibration. The gauges will withstand demanding environmental factors encountered in Civil Engineering construction sites such as tunnels and piling applications.
The data from the VWDT-6000 can be monitored by means of a portable read-out unit or connected to a data logger and distributed if required by telemetry.
Vibrating wire instruments output a frequency signal and are therefore insensitive to resistance changes in connecting cables caused by contact resistance or leakage to ground. Cable may be readily and simply extended on site without special precautions. Gauges may be read up to 1000 meters away from their installed location, without change in calibration.
Instruments may be read by any commercially available Vibrating wire readout system operating on either the pluck pulse or swept frequency excitation principle, provided that these units operate over the frequency range of the instruments. In addition, these instruments can be data-logged by a variety of data-loggers equipped with vibrating wire excitation modules including Campbell Scientific and Datataker, units.
Units are supplied with a ball end to ensure minimum contact point to ensure accurate readings.
Additional information
| Brands | |
|---|---|
| Range |
12.5, 25, 50, 75mm |
| Excitation |
Pluck or swept frequency |
| Thermistor |
3k Ohms at 25 °C |
| Resolution |
0.025% FS |
| Accuracy |
±0.1% FSO |
| Non linearity |
<0.5% FS |
| Operating range |
-20 °C +100 °C |
Reviews (0)
About brand
Geosense Ltd is one of Europe’s leading manufacturers and suppliers of instruments to the geotechnical, civil engineering, mining and environmental industries.
Geosense products are used globally in major projects in more than 68 countries. With a comprehensive in-house design and manufacturing capability, we can provide products not only to tight deadlines but also to suit custom-engineered solutions for specific project requirements.
Geosense specialises in the manufacture of vibrating wire and MEMS sensors, which are used to produce a wide range of instruments. In addition we manufacture automated data acquisition systems to complement our sensors, including wireless systems.
Data Sheets
Related products
VWPHT-3600 SERIES
In stock
The VWPHT-3600 series High Temperature Piezometers are suitable for the extreme environments of temperature and pressure found within applications such as geothermal heat and enhanced oil recovery systems including steam assisted gravity drainage (SAGD) and cyclic steam stimulation (CSS). They are capable of monitoring high temperatures up to 250°C and pressures up to 34.5 MPa.
PRESSURE TRANSDUCER VWT-9000 SERIES
In stock
The Geosense® VWT-9000 Series of Pressure Transducers are designed to be connected directly into hydraulic or pneumatic pressure lines by means of a 1/4” BSPF thread. Other thread sizes are available on request.
They are typically used to monitor uplift pressures within dams and to enable manual standpipe piezometers to be upgraded into an automated data acquisition system.
TILT BEAM
In stock
The Tilt Beam is a lightweight, rigid aluminium beam that is used in conjunction with a Triaxial Tilt Node, a NanoPlus or a NanoMacro.
The tilt beam has been successfully used in many applications, including:
- Movement monitoring of any structure
- Longitudinal settlement
- Tunnel convergence/divergence
- Lateral displacements
PENDULUM SYSTEM
In stock
HPS-3500 (Hanging) and IPS-3000 (Inverted) Pendulums are used to measure the tilt or rotation by measuring the relative internal horizontal displacement of points along a true vertical line. Each has a tensioned, stainless steel wire and the effects of the earth gravitational forces to guarantee a perfectly vertical line between a fixed point and a tensioning mechanism. Typical applications include concrete dams, bridges and high rise buildings.
IMAGING & CAMERA
In stock
The FlatMesh 4G Camera is a best in class solar powered solution for static imagery in remote or industrial areas.
It contains a monochrome digital camera which can take clear, high quality photographs day or night without the use of external illuminators.
The 4G camera connects to a Senceive EdgeHub (with FlatMesh) unit which provides power and connectivity over the cellular network (2G/3G/4G) or existing wired ethernet networks.
HUMIDITY & CORROSION (CorroDec®2G)
In stock
The structural infrastructure must always meet requirements such as performance, stability and durability. These requirements will have a lasting effect on our mobility in the future. The corrosion risk and the corrosion activity of the reinforcing steel largely define these requirements and are determined by various impact and material parameters.
INCLINOMETER SPIRAL SENSOR
In stock
MAGNETIC EXTENSOMETER GXM RANGE
In stock
The GEO-XM settlement system is a magnet extensometer system used typically to monitor settlement and heave in foundations, excavations and embankments.
Data received identifies the depth and position where settlement has occurred as well as the total amount of settlement.
It can also be installed behind retaining structures, such as sheet piles and slurry walls, and above underground openings, such as tunnels and shafts.
Reviews
There are no reviews yet.