VW ANCHOR LOAD CELLS VWLC-5000
The VWLC 5000 series Vibrating Wire Anchor Load Cells consist of a cylinder of high strength steel with 3 to 6 vibrating wire strain sensors (depending on capacity) mounted parallel to the longitudinal axis arranged equidistant around the circumference which measure the compression of the cylinder under load.
They are manufactured with a Center hole to accommodate anchors, rock bolts and tendons.
With the multi-sensor configuration, it is possible to obtain accurate readings under mildly eccentric loading conditions as the sensors are read individually.
The readings from the individual sensors are averaged and when used in conjunction with a calibration factor, supplied with each cell, allow the applied load to be calculated.
In multi-strand anchors it is therefore possible to tension the strands uniformly by monitoring the load in each sensor as appropriate.
The abutment plate (provided locally) is normally made to suit specific site requirements and load distribution plate pairs (supplied by Geosense) should be used to minimise eccentric loading and provide a smooth parallel bearing surface and evenly spread the load to the cell. These should be inserted between the load cell and the anchor head.
| Brands | Geosense |
|---|---|
| Thermistor | 3k Ohms at 25°C |
| Internal diameters | 25, 50, 77, 112, 144, 165, 190, 225, 230mm |
| Accuracy (system accuracy depends on loading conditions) | 0.5% FS (0.25% FS available on request) |
| Resolution | 0.05% FS |
| Output | 1200 – 2800 Hz |
| Temperature range | -20°C to + 80°C |
Related products
VWPHT-3600 SERIES
In stock
The VWPHT-3600 series High Temperature Piezometers are suitable for the extreme environments of temperature and pressure found within applications such as geothermal heat and enhanced oil recovery systems including steam assisted gravity drainage (SAGD) and cyclic steam stimulation (CSS). They are capable of monitoring high temperatures up to 250°C and pressures up to 34.5 MPa.
STRAIN GAUGE PIEZOMETER SGP-3400 SERIES
In stock
The SGP-3400 Series of strain gauge piezometers are designed for monitoring soil pore pressure or changes in water level and are also suitable for dynamic monitoring such as pumping tests.
They are accurate, highly-reliable and suitable for use in the harsh environments often found within civil engineering including water wells, boreholes, dams, reservoirs, rivers, tanks or any other body of water.
DRIVE-IN PIEZOMETERS WP-3400 & SGP-3500 SERIES
In stock
Drive-in piezometers, also referred to as push-in piezometers, are designed for installing in soft clays, organic or fine grained cohesionless soils typically with a SPT-N value less than 10. They are available with a CPT fitting or 1” BSP thread.
Depending on the depth and type of soil, they can either be pushed directly into the soil from ground level to the required depth or pushed into the base of a CPT test or drilled borehole.
IN-PLACE TILT METER MEMS
In stock
PORTABLE MEMS INCLINOMETER
In stock
The MEMS Portable Inclinometer system utilises modern communication and Smart devices to enable the tilt data generated by the probe to be managed, stored and transferred directly from site via FTP, API, email or other communication platforms.
It is available for vertical, inclined and horizontal applications.
TILT BEAM
In stock
The Tilt Beam is a lightweight, rigid aluminium beam that is used in conjunction with a Triaxial Tilt Node, a NanoPlus or a NanoMacro.
The tilt beam has been successfully used in many applications, including:
- Movement monitoring of any structure
- Longitudinal settlement
- Tunnel convergence/divergence
- Lateral displacements
DIGITAL PIEZOMETER – dPiezo
In stock
IPI-X IN PLACE INC – EXT
In stock

Reviews
There are no reviews yet.